View MN101D03D_991710.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MN101D03D
Type ROM (x8-bit) x RAM (x 8-bit) x Package Minimum Instruction Execution Time
MN101D03D 64 K 2K LQFP080-P-1414A *Lead-free 0.10 s (at 4.5 V to 5.5 V, 20 MHz) 0.238 s (at 2.7 V to 5.5 V, 8.39 MHz)*1 125 s (at 2.0 V to 5.5 V, 32 kHz)*2 1 The lower limit for operation guarantee for flash memory built-in type is 4.5 V. * *2 The lower limit for operation guarantee for EPROM built-in type is 2.3 V. * RESET * Watchdog * External 0 * External 1 * External 2 * External 3 * External 4 * External 5 * External 6 * External 7 * Timer 0 * Timer 1 * Timer 2 * Timer 3 * Timer 4 * Timer 5 * Timer 6 * Time base * Timer 7 (2 systems) * Timer 8 (2 systems) * Serial 0 reception * Serial 0 transmission * Serial 1 * Serial 2 * Automatic transfer finish * A/D conversion finish * Key interrupts (8 lines) Timer counter 0 : 8-bit x 1 (square-wave output [timer pulse output], PWM output, event count, remote control carrier output, simple pulse width meausurement function) Clock source ********************* 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Timer counter 1 : 8-bit x 1 (square-wave output [timer pulse output], event count, timer synchronous output) Clock source ********************* 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Timer counter 0, 1 can be cascade-connected. Timer counter 2 : 8-bit x 1 (square-wave output [timer pulse output], PWM output, event count, timer synchronous output, simple pulse width meausurement function) Clock source ********************* 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Timer counter 3 : 8-bit x 1 (square-wave output [timer pulse output], event count, remote control carrier output) Clock source ********************* 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Timer counter 2, 3 can be cascade-connected. Timer counter 4 : 8-bit x 1 (square-wave output [timer pulse output], PWM output, event count, simple pulse width meausurement function) Clock source ********************* 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Timer counter 5 : 8-bit x 1 (square-wave output [timer pulse output], event count) Clock source ********************* 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Timer counter 4, 5 can be cascade-connected. Time base timer Clock source ********************* 1/27, 1/28, 1/29, 1/210, 1/213 , 1/215 of OSC oscillation clock frequency; 1/27, 1/28, 1/29, 1/210, 1/213, 1/215 of XI oscillation clock frequency Timer counter 6 : 8-bit freerun timer Clock source ********************* 1/1 of system clock frequency; 1/1, 1/27, 1/213 of OSC oscillation clock frequency; 1/1, 1/27, 1/213 of XI oscillation clock frequency
Interrupts
Timer Counter
1
MAD00031DEM
MN101D03D
Timer Counter (Continue)
Timer counter 7 : 16-bit x 1 Clock source ********************* either of system clock, OSC oscillation clock, external clock 1 or external clock 2 frequency-divided into 1/1, 1/2, 1/4 or 1/16) (hardware configuration) double buffer type compare register x 2 input capture register x 1 (timer functions) square-wave output (timer pulse output), high-precision PWM output (cycle/ duty continuously variable), event count, simple pulse width measurement function and input capture function Timer counter 8 : 16-bit x 1 Clock source ********************* either of system clock, OSC oscillation clock, external clock 1 or external clock 2 frequency-divided into 1/1, 1/2, 1/4 or 1/16) (hardware configuration) double buffer type compare register x 2 input capture register x 1 (timer functions) square-wave output (timer pulse output), PWM output (duty continuously variable), event count, simple pulse width measurement function and input capture function Watchdog timer Interrupt source **************** runaway detection frequency selection from 1/216, 1/218 and 1/220 of system clock frequency
Serial Interface
Serial 0 : 8-bit x 1 (full-duplex UART/ synchronous type) Synchronous type (MSB or LSB first selectable; 1 to 8 bits arbitrary transmission; continuous transmission, continuous reception and continuous transmission-reception possible by combination with ATC function) Transfer clock source ****** 1/2, 1/4 of system clock frequency; 1/2, 1/4, 1/16, 1/32 of OSC oscillation clock frequency; timer counter 2 to 5 output; 1/3 of frequency of the above clocks Full-duplex UART (built-in baud rate timer, parity check, overrun error/framing error detection, transfer bit selectable from 7 and 8 bits) Serial 1 : 8-bit x 1 (simple I 2C/ synchronous type) Synchronous type (MSB or LSB first selectable; 1 to 8 bits arbitrary transmission; continuous transmission, continuous reception and continuous transmission-reception possible by combination with ATC function) Transfer clock source: ***** 1/2, 1/4 of system clock frequency; 1/2, 1/4, 1/16, 1/32 of OSC oscillation clock frequency; timer counter 2 to 5 output; 1/3 of frequency of the above clocks Simple I 2C (I2C transmission function with single master [9-bit transmission]) Serial 2 : 8-bit x 1 (3-wire synchronous type) Synchronous type (MSB or LSB first selectable; 1 to 8 bits arbitrary transmission; continuous transmission, continuous reception and continuous transmission-reception possible by combination with ATC function) Transfer clock source ****** 1/2, 1/4 of system clock frequency; 1/2, 1/4, 1/16, 1/32 of OSC oscillation clock frequency; timer counter 2 to 5 output; 1/3 of frequency of the above clocks
See the next page for electrical characteristics, pin assignment and support tool.
MAD00031DEM
2
I/O Pins A/D Inputs
I/O Input
67 1
* Common use * Specified pull-up resistor available * Input/output selectable (bit unit) * Common use
10-bit x 8-ch. (with S/H) Conversion Cause 7 ********* A/D control register setting; timer 4, 6 or 8 interrupt; external interrupt 3 or 7; serial 1 interrupt Buzzer output, remote control carrier signal output, high-current drive port x 1
Special Ports Electrical Characteristics
Supply current
Limit Parameter Symbol IDD1 Operating supply current IDD2 IDD3 Supply current at HALT Supply current at STOP IDD4 fx = 32 kHz , VDD = 3 V , Ta = 85C IDD5 VDD = 5 V 20 10 Condition min fosc = 20 MHz , VDD = 5 V fosc = 8.39 MHz , VDD = 5 V *fx = 32 kHz , VDD = 3 V fx = 32 kHz , VDD = 3 V , Ta = 25C typ max 60 25 120 8 mA mA A A A A Unit
* Flash memory built-in type : 300 A max. at VDD = 5 V
Pin Assignment
IRQ3,TCI9,KEY5(P45) SBT2,NLDDMA(P35) NDK,BUZZERS(P06) TM8IO,KEY4(P44)
43
TM4IO,KEY3(P43)
42
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
AN0(PA0) AN1(PA1) AN2(PA2) AN3(PA3) AN4(PA4) AN5,IRQ5(PA5) AN6,IRQ6(PA6) AN7,IRQ7(PA7) VREFP VDD D7,MPB7(P87) D6,MPB6(P86) D5,MPB5(P85) D4,MPB4(P84) D3,MPB3(P83) D2,MPB2(P82) D1,MPB1(P81) D0,MPB0(P80) A15,SDO7(P77) A14,SDO6(P76)
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
10 11 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9
41
TM5IO,KEY2(P42)
NCS3,KEY7(P47)
IRQ4,KEY6(P46)
SBO2,NBR(P33)
TXD,SBO0(P00)
NDKDMA(P37)
RXD,SBI0(P01)
SBI2,NBT(P34)
NSTDMA(P36)
SYSCLK(P07)
SBO1(P03)
SBT0(P02)
SBT1(P05)
SBI1(P04)
VREFM
40 39 38 37 36 35 34 33 32 31
TM4IO,KEY1(P41) LED0,KEY0(P40) LED2(P16) VSS XO XI VSS OSC2 OSC1 VDD2 TM3IO(P13) TM2IO(P12) TM1IO(P11) RMOUT,TM0IO(P10) IRQ0(P20) IRQ1,SENS(P21) IRQ2(P22) P24 ALEMPB(P26) NRST(P27)
MN101D03D
30 29 28 27 26 25 24 23 22 21
20
NWE,NWEMPB(P50)
NRE,NREMPB(P51)
NCS(P52)
A17,NCS1(P53)
A13,SDO5(P75)
A12,SDO4(P74)
A11,SDO3(P73)
A10,SDO2(P72)
LQFP080-P-1414A *Lead-free
3
A16,NCS2(P54)
A9,SDO1(P71)
A8,SDO0(P70)
A7(P67)
A6(P66)
A5(P65)
A4(P64)
A3(P63)
A2(P62)
A1(P61)
A0(P60)
MMOD
MAD00031DEM
MN101D03D
Support Tool
In-circuit Emulator EPROM Built-in Type
PX-ICE101C / D + PX-PRB101D03-LQFP080-P-1414A Type ROM (x 8-bit) RAM (x 8-bit) Minimum instruction execution time MN101DP03FAL 96 K 4K 0.10 s (at 4.5 V to 5.5 V, 20 MHz) 0.238 s (at 2.7 V to 5.5 V, 8.39 MHz) 125 s (at 2.3 V to 5.5 V, 32 kHz) Package LQFP080-P-1414A *Lead-free MN101DF03D 64 K 2K 0.10 s (at 4.5 V to 5.5 V, 20 MHz) 0.238 s (at 4.5 V to 5.5 V, 8.39 MHz) Package LQFP080-P-1414A *Lead-free
Flash Memory Built-in Type
Type ROM (x 8-bit) RAM (x 8-bit) Minimum instruction execution time
MAD00031DEM
4
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd.
2002 JUL

▲Up To Search▲

Price & Availability of MN101D03D

	To Download MN101D03D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .